manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 247 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 247

Chapter 12

12-3

12.1.6 Others

0020-4291

If a machine is brought from a cold to warm room, its inside can start to develop condensation, leading to various problems.

a. condensation on the BD sensor is likely to cause problems associated with E100

b. condensation on the dust-proof glass is likely to cause poor image density in sub scanning direction

c. condensation on the contact sensor of the reader unit or on the copyboard glass can cause light images

d. condensation on the pickup or feed guide can cause paper feed problems

If the problem given in d. above has occurred, dry wipe the units in the feed system. Do not open the package containing a toner cartridge, developing unit, or drum

unit right after it has been brought in from a cold to warm place to avoid condensation. Be sure to leave it alone for a while (1 to 2 hr), opening it after it has become

fully used to the temperature of the site.

12.2 Outline of Electrical Components

12.2.1 Clutch/Solenoid

12.2.1.1 List of Clutches/Solenoids

0020-4292

<Reader Unit>

The reader unit has no clutch/solenoid. 

<Printer Unit>

F-12-1

Symbol

Name

Function

CL201

Manual pickup clutch

Drives the manual pickup roller.

CL202

Cassette feed clutch

Drives the cassette feed roller.

CL203

Registration clutch

Drives the registration clutch.

SL201

Manual pickup solenoid

Drives the manual pickup roller.

SL202

Cassette 1 pickup solenoid

Drives the cassette 1 pickup roller. 

CL203

CL201

SL201

SL202

CL202

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments