manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 169 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 169

Chapter 7

7-1

7.1 Construction

7.1.1 Specifications/Configuration/Operation Methods

0020-4114

Functions and operation methods of the pickup/feeding system are as follows:

Item

Function/Operation method

Pickup method

Cassette

Clow retard

Multi manual feed tray

Duplo separation

Paper stack

Cassette

Plain Paper 300Sheets(64g/m2)
            260Sheets(75g/m2)
            250Sheets(80g/m2)
            120Sheets(90g/m2)

Multi manual feed tray

Plain paper
         Large 50Sheets(64g/m2)*1
         Small 100Sheets(64g/m2)
         Large 50Sheets(75g/m2)
         Small 100Sheets(75g/m2)
         Large 50Sheets(80g/m2)
         Small 80Sheets(80g/m2)
         Large 50Sheets(90g/m2)
         Small 50Sheets(90g/m2)
Thick Paper    50Sheets(105g/m2)
               35Sheets(128g/m2)
Label sheet    1Sheets
OHP            50Sheets
Envelope       10Sheets

Paper size Setting

Cassette

Set by user

Multi manual feed tray

Set by user

Delivery option

Finisher-U2
Inner 2Way Tray-E2

Pickup option

Cassette Feeding Module-J1*2/S1/S2*3
Cassette Feeding Module-K1*2/T1/T2*3

*1 Large:more than B4/LGL,Small:less than B4/LGL

*2 Option only for EUR 

*3 Option only for CN 

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments