Canon iR2318 series Service Manual Download Page 101

Page: 101 / 308

Chapter 3

3-7

3.5 Parts Replacement Procedure

3.5.1 Main Controller PCB

3.5.1.1 Preparation for Removing the image processor

PCB

0020-4330

1) Remove the rear cover.

(page 9-7)

[Removing the Rear Cover]

3.5.1.2 Removing the Image Processor PCB

0020-4331

1) Remove the image processor PCB unit [1].

- 4 flat cables [2]

- 1 connector [3]

- 4 screws [4]

F-3-10

2) Remove the image processor PCB [1].

- 5 screws [2]

F-3-11

3.5.1.3 Procedure after Replacing the Image Processor

PCB

0020-4332

If you have replaced the image processor PCB with a new one, perform the

following operations:

- Using the user support tool, download the latest firmware (System/Boot).

- Input the all value printed on the service label affixed to the rear cover.

Make the following adjustments:

- Correction of output between CIS channels

1) Enter the service mode.

Sequentially press the Additional Functions, # key on the operation panel.

2) Using the upper/lower arrow keys on the operation panel, select "Test".

3) Press the OK key.

4) Using the upper/lower arrow keys on the operation panel, select "Scanner

test".

5) Press the OK key.

6) Using the upper/lower arrow keys on the operation panel, select "CS Out-

put Test".

7) Press the OK key.

8) Select "Yes" and then press the OK key.

After completion of the above steps, contact sensor output correction will be

performed and parameters will be set automatically.

- Read position adjustment (Stream reading: Only when the ADF is installed)

1) Enter the service mode.

Sequentially press the Additional Functions, # key on the operation panel.

2) Using the upper/lower arrow keys on the operation panel, select "Test".

3) Press the OK key.

4) Using the upper/lower arrow keys on the operation panel, select "Scanner

test".

5) Press the OK key.

6) Using the upper/lower arrow keys on the operation panel, select "CS Po-

sition Test".

7) Press the OK key.

8) Select "Yes" and press the OK key.

The optical system starts scanning. Several seconds later, automatic adjust-

ment of the reading position finishes and "OK" appears.

[1]

[2]

[3]

[4]

[1]

[2]

If automatic adjustment fails, "NG" appears. Perform the following

procedure:
Clean the white roller of the DADF and the document glass of the host
machine, and then retry auto adjustment.

Summary of Contents for iR2318 series





















































































































































































































































































































Search results

Summary of Contents for iR2318 series

Reviews:

Canon iR2318 series, Service Manual, Page: 101 / 308

Search results

Summary of Contents for iR2318 series

Reviews: