background image

Application

This manual has been issued by Canon Inc. for qualified persons to learn technical theory, in

-

stallation, maintenance, and repair of products. This manual covers all localities where the prod

-

ucts are sold. For this reason, there may be information in this manual that does not apply to

your locality.

Corrections

This manual may contain technical inaccuracies or typographical errors due to improvements or

changes in products. When changes occur in applicable products or in the contents of this manual,

Canon will release technical information as the need arises. In the event of major changes in the

contents of this manual over a long or short period, Canon will issue a new edition of this manual.

The following paragraph does not apply to any countries where such provisions are inconsistent

with local law.

Trademarks

The  product  names  and  company  names  used  in  this  manual  are  the  registered  trademarks  of  the

individual companies.

Copyright

This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may

not be copied, reproduced or translated into another language, in whole or in part, without the

written consent of Canon Inc.

COPYRIGHT  © 2001 CANON INC.

Printed in Japan 

Caution

Use of this manual should be strictly supervised to avoid disclosure of confidential information.

Summary of Contents for iR1018





















Reviews: