manualshive.com logo in svg

Canon iPF830 Series, Basic Manual

Share
Download
Canon iPF830 Series Basic Manual Download Page 72

5

 

Push down the release lever (a) as shown as you
gently return all ink tank lock levers to the original po-
sition.

6

 

Close the Ink Tank Cover.
At this point, ink is drawn out from inside the tubes.

Important

•

Do not remove the Maintenance Cartridge except when the message for replacing it is displayed.
If you remove the Maintenance Cartridge while ink is being drawn out, the ink may leak out.

7

When the process is finished, "

Preparations for moving the printer finished. Turn the power off

" is dis-

played.
When this happens, replace the Maintenance Cartridge currently being used with a new Maintenance Car-
tridge.

8

 

Press the 

Power

 button and turn off the printer.

Pack the printer

1

Disconnect the power cord and interface cable, as well as the Media Take-up Unit cable.

Important

•

Turn off the printer before you unplug it. It may damage the printer if you unplug it before it is off and
transfer it in that state. If you accidentally unplug the printer, plug it in again, reinstall the ink tanks, and
follow this procedure again.

a

 

 

 

Preparing to Transfer the Printer

                                                                                                                                                                   

iPF830 Series

                                                                                                                                                                                                                      

Basic Guide

   

Printer Relocation

Preparing to Transfer the Printer

 

72

Summary of Contents for iPF830 Series



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands