manualshive.com logo in svg

Canon iPF720 - imagePROGRAF Color Inkjet Printer, Service Manual

Share
Download
Canon iPF720 - imagePROGRAF Color Inkjet Printer Service Manual Download Page 189

7.2 Special Mode

7.2.1 Special Modes for Servicing

0014-3355

This printer supports the following special modes in addition to the service mode:

- PCB replacement mode
- Download mode
- Counter display mode

1. PCB replacement mode

This mode is used when replacing the main PCB or MC relay PCB.
By executing this mode,
- Backup data of the settings and counter values stored in the MC relay PCB are moved to the new main PCB. 
- The data such as the settings and counter values are copied to the MC relay PCB. 

a) Entering the PCB replacement mode
Follow the same procedure as that for entering the service mode.
(With the "Paper Source" button and "Information" button pressed down, turn on the "Power" button.)
When the printer starts up, compare the serial number memorized in the main PCB's EEPROM with that memorized in the MC relay PCB's EEPROM. If
they do not match, or no serial number is memorized in either EEPROM, enter the PCB replacement mode.
While you are in the PCB replacement mode, the MESSAGE LED, roll media LED, and ONLINE LED are lit.

b) Procedure

Select "CPU BOARD" or "MC BOARD" using the [

] and [

] buttons, and then press the [OK] button to determine it.

- CPU BOARD
Select this after replacing the main PCB.
The data in the MC relay PCB is copied to the main PCB.

- MC BOARD
Select this before replacing the main PCB.
The data in the main PCB is copied to the MC relay PCB.
Use this when the MC relay PCB is a new one.

c) Exiting the PCB replacement mode 
Turning off the Power button of the printer allows you to exit the PCB replacement mode. 

For details on how to replace the PCB, see Parts Replacement Procedure > Disassembly/Reassembly > Points to Note on Disassembly and Reassembly >
Boards. 

2. Download mode

Use this mode only when updating the firmware without performing initialization.

a) Entering the download mode
1) Turning off the Power button of the printer.
2) With the "Stop" and "Information" buttons pressed down, turn on the Power button of the printer.
   * Keep pressing the above buttons until "Initializing" appears on the display.

b) Procedure
When "Download Mode/Send Firmware" is shown on the display, transfer the firmware. 
When downloading of the firmware is completed, the printer is turned off automatically.

3. Counter display mode

Use this mode to view only printer counter information.

a) Invoking counter display mode 
1) Press the [MENU] button to keep [Information] > [System Info] selected.

2) Press the [

] button whole holding down the [MENU]  [OK] button to invoke counter display mode.

b) How to view counter display mode 
- S/N: Unit serial number
- CNT: Number of copies printed in A4 terms (unit: copies)

Summary of Contents for iPF720 - imagePROGRAF Color Inkjet Printer













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands