Canon iPF6100 - imagePROGRAF Color Inkjet Printer Service Manual Download Page 37

Page: 37 / 367

Chapter 1

1-25

1.5.6 Carriage

0016-8157

F-1-22

[1] Printhead lock cover

This cover is used to lock the printhead. Open this cover when installing the printhead.

[2] Printhead

The printhead incorporated nozzles. It is an important part for printing.

[3] Printhead lock lever

This lever is used to lock the printhead. Open this lever when installing the printhead.

[4] Wire guide

This stay is used as an ink tube guide.

[4]

[2]

[1]

[3]

[2]

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer















































































































































































































































































































































































Search results

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer

Reviews:

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Brands by name

Popular brands

Canon iPF6100 - imagePROGRAF Color Inkjet Printer, Service Manual

Search results

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer

Reviews:

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Brands by name

Popular brands