Canon iPF6100 - imagePROGRAF Color Inkjet Printer Service Manual Download Page 357

Page: 357 / 367

Chapter 8

8-24

8.4 Sevice Call Table

8.4.1 Service Call Errors

0016-8357

* Codes represent the numbers that are displayed in DISPLAY in service mode.

T-8-4

Display massage

Code*

Condition detected

Action

ERROR E141-4046

Call for service.

E141-4046 Number of recovery

rotations reaching 50,000 or
more

Replace the purge kit.

ERROR E141-4047

Call for service.

E144-4047 Supply count error

Replace the ink supply unit.

ERROR E141-4001

Call for service.

E146-4001 Borderless/flow idle

ejection/mist recovery
counter full

Replace the platen duct unit.

ERROR E141-403E

Call for service.

E161-403E Abnormal temperature rise

in printhead R

Replace the printhead.

ERROR E141-4034

Call for service.

E196-4034 Multi sensor unit version

error

Replace the multi sensor unit

ERROR E141-404A

Call for service.

E194-404A Non-discharging nozzle

count error

Replace the head management sensor
unit

ERROR E141-403F

Call for service.

E196-403F Abnormal temperature rise

printhead L

Replace the printhead

ERROR E141-4040

Call for service.

E196-4040 Checksum error

Replace the main controller PCB

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer















































































































































































































































































































































































Search results

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer

Reviews:

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Brands by name

Popular brands

Canon iPF6100 - imagePROGRAF Color Inkjet Printer, Service Manual

Search results

Summary of Contents for iPF6100 - imagePROGRAF Color Inkjet Printer

Reviews:

Related manuals for iPF6100 - imagePROGRAF Color Inkjet Printer

Brands by name

Popular brands