manualshive.com logo in svg

Canon imageRUNNER C3480, Sending And Facsimile Manual Sending And Facsimile Manual

Share
Download
Canon imageRUNNER C3480 Sending And Facsimile Manual Sending And Facsimile Manual Download Page 335

Communications Settings

11-9

11

System Mana

ger Settin

gs

<Allow MDN Not Via Server>:

NOTE

 

•

If you set the divided data RX timeout time to '0', no divided data RX timeout time is 
set.

•

For I-fax, when <Use Send Via Server> is set to 'Off', even if you enter the 
maximum data size for sending, there is no size limit on the data that is sent.

•

The maximum data size for sending can be set in 1 MB increments. If the size of an 
e-mail exceeds the set limit, the e-mail message is split up by page and sent out as 
smaller e-mail messages, each of which is within the set limit. I-fax data that 
exceeds the set limit is handled as an error, and is not sent. For more information, 
contact your local authorized Canon dealer.

 

Fax Settings

This section describes settings that the System Manager can make, including how 
to set the Send Start Speed, Receive Start Speed, RX (Receive) mode, and how to 
register a password. It also describes how to set, change, and erase settings for 
transferring received documents, and how to enable or disable certain settings.

NOTE

 

This mode is available only if the optional Super G3 FAX Board or Super G3 Multi-Line 
Fax Board is installed.

■

Send/Receive Start Speed

This function enables you to change the send and receive start speeds, which is useful 
when there is difficulty initiating the sending or receiving of a document.

■

Receive Password

This function enables you to set an optional ITU-T standard password. If a subaddress is 
not set in a document that was received from another party using the ITU-T standard, an 
RX password check takes place. If the RX password found does not match the RX 
password set with this mode, or if an RX password is not attached to the document, the 
document is not received.

NOTE

 

ITU-T stands for International Telecommunication Union-Telecommunication 
Standardization Sector, which is the group that makes recommendations towards the 
standardization of worldwide telecommunications.

[On]: Allows the sending of MDN (Mail Delivery Notification) mail without going 

via a mail server.

[Off]: Does not allow the sending of MDN (Mail Delivery Notification) mail without 

going via a mail server.

Summary of Contents for imageRUNNER C3480





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands