5
5
5-2
5-2
Adjustment > Main Controller > Main controller PCB 1
Adjustment > Main Controller > Main controller PCB 1
Main Controller
HDD
How to Replace
the Parts
Refer to “Removing the HDD”.
Before
Replacing
1) Backup of the set/registered data
Use the Remote UI.
Management Settings > Data Management > Import/Export
Target data:
• Address List
• Forwarding Settings
• Settings/Registration
• Web Access Favorites
• Printer Settings
• Paper Information
2) Printing the set/registered data
Use the service mode.
(Lv.1) COPIER > FUNCTION > MISC-P > USER-PRT
List of the set/registered data which cannot be backed up is printed."
Aftter Replacing 1) HDD format
1-1) Start with the safe mode. (While pressing 2 and 8 keys simultaneously,
turn ON the main power switch.)
1-2) Use SST to format all partitions.
2) Downloading system software
2-1) Use SST to download the system software (System, LANG, RUI and
others).
3) Initializing the key, certificate and CA certificate
(Lv.2) COPIER > FUNCTION > CLEAR > CA-KEY
4) Turning OFF and ON the main power switch
5) Restoring the backup data
Use the Remote UI.
Management Settings > Data Management > Import/Export
6) Resetting/registering the data
While referring to the list of set/registered data which was printed before
replacement, reset/register the data.
7) When the user generates and adds the encryption key, certificate and/or CA
certificate, request the user to generate them again.
8) Executing “Auto Adjust Gradation (Full Adjust)” Settings/Registration mode:
Adjustment/Maintenance > Adjust Image Quality > Auto Adjust Gradation
When using
the Card
Reader and
imageWARE
Accounting
Manager
1) Go to COPIER > FUNCTION> INSTALL > CARD and enter the numerical value
of the leading card which is used for Department ID.
Then, press “OK” button. (e.g.: If No.1 to No.1000 cards are used for
Department ID, enter “1” of the leading card.)
2) After turning OFF and ON the main power switch, perform the following
operations from Settings/Registration mode.
• In Management Settings > User Management > Department ID Management >
Page Totals, be sure that “ID00000001” to “ID00001000” are created.
• Set the following: Preferences > Network > TCP / IP Settings > IPv4 Settings>IP
Address Settings > IP Address, Gateway Address, Subnet Mask
• In Management Settings > User Management> System Manager Information
Settings> System Manager ID and System PIN, register any number for them.
Then, turn OFF and ON the main power switch.
If “System Manager ID” and “System PIN” are not registered, “card registration
to device” cannot be executed for the imageWARE Accounting Manager setting
operation.
3) Download the card ID from imageWARE Accounting Manager to the Main Body
again.
4) After downloading is completed, go to Management Settings > User
Management > Department ID Management > Page Totals. Be sure that only
the downloaded card ID is displayed.
5) Print using the user card registered from imageWARE Accounting Manager.
Be sure that the card information used for the target devices of imageWARE
Accounting Manager is collected.
Points to Note when Using the System Software-installed HDD When using the
HDD which was installed the system software of the other machine (different serial
number), be sure to format the HDD after the installation.
If the HDD is not formatted, the operation cannot be guaranteed.
Points to Note
when Using
the System
Software-
installed HDD
When using the HDD which was installed the system software of the other
machine (different serial number), be sure to format the HDD after the installation.
If the HDDis not formatted, the operation cannot be guaranteed.
Main controller PCB 1
How to Replace
the Parts
Refer to “Removing the Main Controller PCB 1”.
Operation at
Replacement
Transferring the parts from old PCB to new PCB
• DDR2-SDRAM (2 pc.)
• Flash PCB
• TPM PCB
Resetting/registering the data is not necessary after Main Controller PCB 1 is
replaced.
T-5-1
T-5-2