manualshive.com logo in svg

Canon imageRUNNER ADVANCE C3330 Series, Troubleshooting Manual, Page: 106 / 200

Share
Download
Canon imageRUNNER ADVANCE C3330 Series Troubleshooting Manual Download Page 106

Copier Color | iR-ADV C3330/C3325/C3320 Series |

Noise (squeaking noise) from the right rear side of Main Body

[Symptom]

Noise (squeaking noise) may occur from around the right rear side [a] of the Main Body.

[Cause]

If enough grease is not applied or no grease is applied to the side surface of the core of the swing gear in the Fixing Drive Unit,
the core rubs against the inner face of the gear. As a result, the symptom occurs.
If the symptom occurs during initial rotation after the power is turned ON or after a button on the touch panel is pressed, the above
cause is highly likely a main factor.

[Service work]

1) Remove the Fixing Drive Unit, by referring to Service Manual "Disassembly/Assembly > Fixing System > Removing the Fixing
Drive Unit."
2) Remove the cable [a] from the cable guide in the Fixing Drive Unit. Remove the 3 screws [b] and the Cover [c].

3) Remove the 3 gears (1), (2), and (3) in this order.

101

Summary of Contents for imageRUNNER ADVANCE C3330 Series









































































































































































































Reviews:

No comments