8
8
8-181
8-181
Service Mode > SORTER > FUNCTION
Service Mode > SORTER > FUNCTION
SORTER
ADJUST
SORTER >ADJUST
CLCT-SB
Adjustment of switchback position
Lv.1 Details
To adjust the paper switchback position when the paper is delivered
to the Processing Tray.
Use case
When a stacking failure due to curl at the Processing Tray occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-50 to 50
Unit
0.1 mm
Default value
0
STP-2P
Adj front/rear 2-staple position
Lv.1 Details
To adjust the front/rear 2-staple position on Finisher.
As the value is incremented by 1, the staple position moves by
0.1mm.
+: Toward front
-: Toward rear
Use case
When the front/rear 2-staple position is displaced
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
-25 to 25
Unit
0.1 mm
SFT-AMT1
Adj shft amnt of Shft Roll (frt)
Lv.1 Details
To adjust the front shift amount of the Shift Roller.
As the value is incremented by 1, the Shift Roller moves toward the
guide by 0.1 mm.
Use case
When the front shift amount of the paper is inappropriate
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 50
Unit
0.1 mm
Default value
0
SFT-AMT2
Adj shft amnt of Shft Roll (Rear)
Lv.1 Details
To adjust the rear shift amount of the Shift Roller.
As the value is incremented by 1, the Shift Roller moves toward the
guide by 0.1 mm. (The paper length to be detected is shortened by
0.1mm.)
Use case
When the rear shift amount of the paper is inappropriate
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-50 to 50
Unit
0.1 mm
Default value
0
SORTER >ADJUST
STP-NTN
Adj of Staple Needle pitch (A4)
Lv.1 Details
To adjust the pitch between needles for 2-point stapling.
As the value is incremented by 1, the pitch between needles
becomes wider by 0.27 mm.
Use case
When the pitch between needles for 2-point stapling is inappropriate
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-8 to 8
Unit
0.27 mm
Default value
0
INSTP-F1
Adj of front staple position
Lv.1 Details
To adjust the paper pull-in amount of the Gripper at the time of front
1-point stapling.
As the value is incremented by 1, the paper pull-in amount is
increased by 0.1 mm.
Use case
When misalignment occurs at the front staple position
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-50 to 50
Unit
0.1 mm
Default value
0
INSTP-R1
Adj of rear staple position
Lv.1 Details
To adjust the paper pull-in amount of the Gripper at the time of rear
1-point stapling.
As the value is incremented by 1, the paper pull-in amount is
increased by 0.1 mm.
Use case
When misalignment occurs at the rear staple position
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-50 to 50
Unit
0.1 mm
Default value
0
FUNCTION
SORTER > FUNCTION
FIN-CON
Controller PCB RAM clear
Lv.1 Details
To execute the RAM clear of Finisher Controller PCB to delete all the
adjustment contents and counter information.
Use case
When E505-0001 (EEPROM error) occurs
Adj/set/operate method 1) Select the item, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
- Output the service mode setting values by P-PRINT before
execution. After execution, enter the necessary setting values.
- RAM clear is executed after the main power is turned OFF/ON.
Related service mode
COPIER> FUNCTION> MISC-P> P-PRINT
T-8-74
T-8-75
