Canon imageRUNNER ADVANCE C2000 Series Technical Workbook Download Page 120

Page: 120 / 175

pg. 118

Symptom

Streaky display on the LCD control panel screen occurred upon turning the main power SW on after
installation.

Cause

The connector on the Control Panel Cable which connects to the Main Controller PCB 1 was inserted
askew.

Service work

Properly insert the connector on the Control Panel Cable.

Title

No display appears on Control Panel LCD due to poorly connected interface cable at power-on

Symptom

When turning the power on, the control panel LCD may have no display.

Cause

Because the contact surface [a] of the interface cable found on the back of the control panel is not securely
fitted as shown in the photo [B]. The photo [A] shows the state that the cable is properly inserted.

Summary of Contents for imageRUNNER ADVANCE C2000 Series
















































































































































































Search results

Summary of Contents for imageRUNNER ADVANCE C2000 Series

Reviews:

Related manuals for imageRUNNER ADVANCE C2000 Series

Brands by name

Popular brands

Canon imageRUNNER ADVANCE C2000 Series, Technical Workbook

Search results

Summary of Contents for imageRUNNER ADVANCE C2000 Series

Reviews:

Related manuals for imageRUNNER ADVANCE C2000 Series

Brands by name

Popular brands