Canon imageRUNNER 5055 series, Service Manual

Page: 548 / 596

Chapter 17
17-52
17.7 TEST (Test Print Mode)
17.7.1 COPIER
17.7.1.1 COPIER List
0015-5967
iR5065 / iR 5055 / iR5075 / / /
<PG>
T-17-62
<NETWORK>
T-17-63
1) Hold down the control panel switch to start shut-down sequence. When ready, turn off the main power switch.
2) Connect the network cable to the machine, and turn on the main power switch.
3) Inform the user's system administrator that the installation of the machine is over, and ask him/her to make network settings.
4) Inform the system administrator that you are going to check the network connection, and find out the remote host address (i.e., the IP address of a PC terminal
on the user's network).
5) Make the following selections in service mode: COPIER>TEST>NETWORK>PING; then, type in the IP address you obtained in step 4) When ready, press the
OK key and then the Start key.
- The indication will be 'OK' if the connection to the network is correct. (End the work.)
- If the indication is 'NG', on the other hand, check the connection of the network cable; if the cable is normal, go to step 6). If a fault is found in the cable, correct
it, and go back to step 5).
6) Make the following selections in service mode: COPIES>TEST>NETWORK>PING. Then, enter the local host address (i.e., IP address of the machine), and
press the OK key.
- If the indication is 'NG', suspect a fault in the IP address of the machine or of the network controller. Ask the system administrator for a check on the IP address,
or replace the main controller PCB.
- If the indication is 'OK', on the other hand, the network settings and the network controller may be assumed to be normal. If so, suspect a fault in the user's network
environment; report to the system administrator for remedial work.
7) Make the following selections in service mode: COPIER>TEST>NETWORK>PING; then, enter the local host address (i.e., IP address of the machine), and
press the OK key.
- If the notation is 'NG', suspect a fault in the IP address of the machine or in the network controller. Contact the system administrator to obtain the correct IP address
or replace the main controller PCB.
- If the notation is 'OK', the network settings and the network controller may be assumed to be free of faults. The fault is likely to be in the user's network environ-
ment. Contact the system administrator for remedial action.
COPIER > TEST > PG
Sub-item Description Level
TYPE Enter the type No. of the desired test print, and press the Start key to print out a test print. (Be sure to return it to '0' after printing.)
0: image from CCD (normal print)
1: grid
2: 17 gradations (error diffusion; T-BIC)
3: 17 gradations (dither screen)
4: blank 00H
5: halftone 80 H (error diffusion; T-BIC)
6: halftone 80 H (dither screen)
7: solid black FFH
8: horizontal line (space: 27 dots; line width: 4 dots)
9: horizontal line (space: 50 dots; line width: 6 dots)
10: horizontal line (space: 3 dots; line width: 2 dots)
11: halftone 60H (error diffusion; T-BIC)
12: halftone 60H (dither screen)
13: halftone 30H (error diffusion: T-BIC)
14: halftone 30H (dither screen)
15: 17 gradations (text mode)
16: 17 gradations (text/photo mode)
17: 17 gradations (print photo mode)
18: 17 gradations (film photo mode)
19: for R&D
20: 17 gradations (PDL screen: medium resolution)
21: 17 gradations (PDL screen: low resolution)
22: 17 gradations (PDL screen: high resolution)
23 to 30: for R&D
1
TXPH Use it to switch between text mode or photo mode for test printing.
1
setting: 0 to 4
PG-PICK Use it to select the source of paper for test printing.
1: right deck
2: left deck
3: cassette 3
4: cassette 4
5-6: not used
7: side deck
8: multifeeder
1
2-SIDE Use it to select the output mode for test printing.
setting
0: simplex
1: duplex
(at time of shipment/upon RAM initialization: 0)
1
PG-QTY Use it to select the output mode for test printing.
Use it to set a copy count for test printing.
1 to 999 (default: 1)
1
COPIER > TEST > NETWORK
Sub-item Description Level
PING Use it to check the connection between the machine and a network (only if TCP/IP).
Use it when checking the connection at time of installation or in the event of a network connection fault.
1