Canon imageRunner 330 Service Manual Download Page 90

Page: 90 / 660

CHAPTER 4 IMAGE FORMATION SYSTEM

4-8

B. Shading Correction

The output of the CCD does not necessarily match the light reflected by an original (although

the original may have an even density) for the following reasons:

1. The sensitivity differs from one pixel of the CCD to another.

2. The degree of lens transmission is different between middle and edges.

3 The intensity of the scanning lamp is different between middle and edges.

4. The scanning lamp deteriorates.

The resulting variations are corrected by means of shading: shading correction executed for

each copying run, and shading auto correction whose target value is set in service mode.

1. Shading Auto Correction

Shading auto correction is executed in service mode (FUNCTION>CCD>MAN-ADJ).

In shading auto correction, the density of the white standard plate and white paper is measured

(by the CCD PC), and the collected data is stored in memory. The data is then subjected to

computation, and the result will be used as the "target value" at time of shading correction.

2. Shading Correction

Shading correction is executed for each scan of an original. The light of the scanning lamp is

directed to the standard white plate (Figure 4-301), and the light reflected by the plate is converted

into digital signals by the CCD PCB. The resulting digital signals are sent to the shading circuit on

the image processor PCB as shading data.

The shading circuit compares the shading data against the target value stored in memory, and

sets the difference as the shading correction value.

The shading correction value is used to correct the variation among the pixels of the CCD

occurring during scanning operation, thereby evening out the image density level.

Figure 4-301

Figure 4-302

Standard white plate

Scanning lamp

No. 1 mirror

No. 2 mirror

No. 3 mirror

Lens

CCD

CCD output

Original density

Standard white plate

Characteristic
before correction

Target value

Measurement data

Characteristic
after correction

Summary of Contents for imageRunner 330
















































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for imageRunner 330

Reviews:

Related manuals for imageRunner 330

Brands by name

Popular brands

Canon imageRunner 330, Service Manual

Search results

Summary of Contents for imageRunner 330

Reviews:

Related manuals for imageRunner 330

Brands by name

Popular brands