manualshive.com logo in svg

Canon imagePASS-A2, Service Manual

Share
Download
Canon imagePASS-A2 Service Manual Download Page 53

S

YSTEM

 S

OFTWARE

53

5 Click Server > Backup/Restore, and then click the Restore button.

6 In the Restore dialog box, browse to the configuration file that you created earlier, and click 

Open.

Installing system software through an Ethernet port

To install system software through an Ethernet port, you will need the following:

• Ethernet crossover cable (4-pair/8-wire, short-length)

To determine whether the cable you are using is a Ethernet crossover cable, compare the 
connectors on the cable. The ribbon sequence on the connectors of a Ethernet crossover 
cable are 

not

 identical.

• Computer with Windows 2000, Windows XP, Windows Vista, or Windows 7 

–

A DVD drive, built-in or attached

–

Support for 100BaseTX or 1000BaseT

–

1.5GB minimum memory capacity

• System Software DVD

The System Software DVD contains the system software and the Fiery System Software 
Installer.

Summary of Contents for imagePASS-A2



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands