Canon imageFormula DR-6010C User Manual Download

Page: 52 / 142

Chapter 3

Basic Operation

3-22

Scan Panel Functions

The Scan Panel has the following functions.

Start button

If Feeding Option is set to “Panel-Feeding,” clicking this button starts scanning.

Stop button

Stops scanning.

Job display

When the Start and Stop functions are assigned to the job buttons, [Start] and [Stop] are shown

here.

Note

If nothing is shown on the job display, the Start and Stop functions are not assigned to the job

buttons. In this case, you should use the Start and Stop buttons on the Scan Panel.

Batch separation button

After selecting [Panel] as the batch separation setting on the [Others] tab, if you enable batch

separation from the application and start scanning, this button becomes active when scanning of

the current document completes, and scanning stops.

When clicked, this button depresses and remains depressed while scanning with batch

separation continues, until scanning of the current document completes, and scanning stops.

The button then returns to normal.

Summary of Contents for imageFormula DR-6010C















































































































































Search results

Summary of Contents for imageFormula DR-6010C

Reviews:

Related manuals for imageFormula DR-6010C

Brands by name

Popular brands

Canon imageFormula DR-6010C, User Manual

Search results

Summary of Contents for imageFormula DR-6010C

Reviews:

Related manuals for imageFormula DR-6010C

Brands by name

Popular brands