Canon imageCLASS MF273dw User Manual Download Page 577

Page: 577 / 633

The machine may be set to Shared Key Authentication, and the wireless LAN router may be set to Open

System Authentication. Change the WEP setting according to the authentication method you are using.

When Using Open System Authentication
Connect to the wireless LAN using either of the following methods:

●

Connect with the access point setup method. Connecting to a Wireless LAN by Searching for a
Router (Access Point Setup Method)(P. 63)

●

Using the Manual Setup Method, connect with the WEP authentication method set to [Open System].
Connecting to a Wireless LAN by Setting the Details (Manual Setup Method)(P. 66)

When Using Shared Key Authentication
On the wireless LAN router, change the WEP authentication method to "Shared Key", and connect again.

For the setup method, see the manual of the wireless LAN router or contact the manufacturer.

Device will restart to connect using Easy Connection via PC. Is it OK?

An error occurred, preventing the machine from connecting in Access Point Mode. Alternatively, an error occurred

when starting cableless setup mode.

Restart the Machine, and Start Cableless Setup Mode Again.

Administrator privileges are required.

[Home] on the operation panel [Menu] [Preferences] [Network] [Easy Connection via PC] [Yes]
start the settings on the computer

Direct Connection terminated.

The connection with a mobile device was terminated.

Directly Connect Again.

Connecting a Mobile Device Directly to the Machine (Direct Connection)(P. 290)

Easy Conn. via PC ended due to timeout Device will restart.

30 minutes have elapsed since the start of the cableless setup mode without connecting to the computer.

Restart the Machine, and Start Cableless Setup Mode Again.

Administrator privileges are required.

Touch Panel Model

[Home] on the operation panel [Menu] [Preferences] [Network] [Easy Connection via PC]
[Yes] start the settings on the computer

5 Lines LCD Model

[Home] on the operation panel [Menu]

[Preferences]

[Network]

[Easy

Connection via PC]

start the settings on the computer

Encryption key is not set correctly. Check the encryption key settings.

The network key (encryption key) of the wireless LAN router (access point) is not configured correctly on the machine.

Alternatively, the WEP authentication method of the machine does not match that of the wireless LAN router.

Reset the Network Key.

Troubleshooting

568

Summary of Contents for imageCLASS MF273dw


























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for imageCLASS MF273dw

Reviews:

Related manuals for imageCLASS MF273dw

Brands by name

Popular brands

Canon imageCLASS MF273dw, User Manual

Search results

Summary of Contents for imageCLASS MF273dw

Reviews:

Related manuals for imageCLASS MF273dw

Brands by name

Popular brands