Canon G3620 Online Manual Download Page 101

Page: 101 / 335

Cleaning Paper Feed Rollers

If the paper feed roller is dirty or paper powder is attached to it, paper may not be fed properly.

In this case, clean the paper feed roller.

You need to prepare: three sheets of A4 or Letter-sized plain paper

Check that printer is turned on.

Remove any paper from the rear tray.

Press the

Setup

button, use the button to select

Maintenance

, and press the

button.

LCD and Operation Panel

Clean the paper feed rollers without paper.

Use

button to select

Roller Cleaning

and press

button.

The paper feed roller will rotate as it is cleaned without paper.

Clean the paper feed rollers with paper.

Make sure that the paper feed rollers have stopped rotating, and then load three sheets of A4
or Letter-sized plain paper in the rear tray.

Loading Plain Paper / Photo Paper

Press the

button.

The printer starts cleaning. The cleaning will be complete when the paper is ejected.

If the problem is still not resolved with the operation described above, follow the operation below.

1. Turn off the power and then unplug the power cord.

2. While rotating the paper feed rollers (A) located inside the rear tray more than two laps, wipe them with

a cloth tightly squeezed after moistening.

Do not touch the paper feed rollers with your fingers. Paper feeding performance may be degraded.

101

Summary of Contents for G3620
















































































































































































































































































































































Search results

Summary of Contents for G3620

Reviews:

Related manuals for G3620

Brands by name

Popular brands

Canon G3620, Online Manual

Search results

Summary of Contents for G3620

Reviews:

Related manuals for G3620

Brands by name

Popular brands