Canon Finisher-AK1, Service Manual

Page: 236 / 374

5
5
5-65
5-65
Adjustment > Auxiliary Adjustment > Outline
Adjustment > Auxiliary Adjustment > Outline
Auxiliary Adjustment
Outline
CAUTION: Setting the Dip Switch
If setting the Dip Switch, the Delivery Tray setting on the host machine side returns to
the default.
After setting the Dip Switch, it is necessary to execute the Delivery Tray setting on the
host machine side again.
Except for some items, the adjustment and setting can input from the both devices of the host
machine (service mode) and the finisher (Dip switch).
The input value is memorized in the EEPROM of finisher controller. Regardless of the input
device (host machine or finisher), the setting range and unit are same, and the final input
value is effective.
Item
Bit setting of DSW1
in the finisher
controller PCB
Service mode Range Default Reference
Bufferless Mode ON:1, 3, 8 SORTER> OPTION
>BUFFSW
0 to 4 0 p. 5-96
Adjustment in the Case
of Failure in Stacking
Performance of Tray
(upper curl)
ON:1, 3, 6, 7 SORTER>OPTION
>CURLSW
0 to 2 0 p. 5-102
Adjustment in the Case
of Failure in Stacking
Performance of Tray
(lower curl)
ON:1, 3, 6, 7 SORTER>OPTION
>CURLSW
0 to 2 0 p. 5-104
Adjustment in the Case
of Failure in Stacking
Performance of Tray
(runon of paper when
using thin paper)
ON:1, 3, 7 SORTER>OPTION
>TRYEJCT
0 to 1 0 p. 5-106
Adjustment in the Case
of Canceling Limit for
Tray Stack
ON:1, 3, 5 SORTER>OPTION
>TRYOVER
0 to 1 0 p. 5-108
Setting of Pressless
Mode
ON:1, 3, 4 SORTER>OPTION
>SDLPRS
0 to 3 0 p. 5-120
T-5-8
At the occurrence of the following symptoms or at adjustment timing, perform the appropriate
adjustment.
Adjustment Type Symptom, adjustment timing Reference
Adjusting Position of
Tray A, B
When replacing the Tray A/B Unit p. 5-67
Adjusting Position of
Feed Belt
When displacement occurs with delivered stack p. 5-68
Adjusting Staple
Position (1-stapling at
the rear)
When staple position (rear 1-point stapling) is displaced p. 5-70
Adjusting Staple
Position (1-stapling at
the front)
When staple position (rear 1-point stapling) is displaced p. 5-73
Adjusting Staple
Position (2-stapling
positions)
When staple position (2-point stapling) is displaced p. 5-76
Adjusting Delivery of
Staple Stack (lower
delivery)
When displacement of paper occurs (on the cover
and the 1st to 3rd sheets) at the time of stapled stack
delivery (lower delivery)
p. 5-78
Adjusting Delivery of
Staple Stack (saddle
delivery)
When displacement of paper occurs (on the cover
and the 1st to 3rd sheets) at the time of stapled stack
delivery (saddle delivery)
p. 5-81
Saddle Stitch/Fold
Placement Adjustment
When saddle stitch or fold position is displaced p. 5-84
Adjusting Saddle
Stitching Position
When stitch position (saddle delivery) is displaced p. 5-88
Adjusting Saddle
Folding Position
When fold position (saddle delivery) is displaced p. 5-90
Adjusting Position of
Saddle Lead Edge
Stopper
When saddle fold position (saddle delivery) is displaced p. 5-91
Adjusting Position
for Saddle Alignment
Width
When saddle alignment width is not correct p. 5-94
Bufferless Mode • When alignment failure occurs with the 2nd set (the
first 3 sheets) at the time of making multiple sets of
copy
• When paper corner bend occurs
• When Buffer Path 2 Sensor stationary jam (jam
code: 1109) occurs
p. 5-96
Adjusting Assist
Stopper Position
When the paper on the top of the stapled stack is
misaligned
p. 5-97
Adjusting Height of
Staple Inlet Guide
• When stacking failure occurs on the tray with thin
paper
• - When staple alignment failure occurs
p. 5-98