Canon FAXPHONE L190 Service Manual Download Page 84

Page: 84 / 511

4-8

Disassembly/Assembly > List of Parts > Single-sided Printer Unit > List of Solenoid

■

List of Solenoid

[1]

No.

Name

Reference

Remarks

[1]

Pickup Solenoid

F-4-11

●

List of Sensor

[1]

[2]

[3]

[4]

[5]

[6]

No.

Name

Reference

Remarks

[1] Encoder Sensor

[2] Multi Pickup Sensor

[3] Toner Sensor
[4] Paper Leading Edge Sensor
[5] Paper Width Sensor
[6] Fixing Delivery Sensor

F-4-12

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Search results

Summary of Contents for FAXPHONE L190

Reviews:

Canon FAXPHONE L190, Service Manual, Page: 84 / 511

Search results

Summary of Contents for FAXPHONE L190

Reviews: