Canon FAXPHONE L190 Service Manual Download Page 485

Page: 485 / 511

8-2

Service Mode > Overview > Service Mode Menu

Overview

Entering Service Mode.

Contact the sales company for the method to enter service mode.

Service Mode Menu

Service mode

COPIER

FEEDER

FAX

TESTMODE

DISPLAY

I/O

ADJUST

FUNCTION

OPTION

COUNT ER

SSSW

NUM

NCU

SYSTEM

SCAN

ADJUST

FUNCTION

Service mode for copier

State display mode

Adjustment mode

Operation / inspection mode

I/O display mode

Counter mode

Specification setting mode

Adjustment mode

Operation / inspection mode

ADF service mode

FAX service mode

Service mode for test print, operation check, etc.

Bit switch registration mode

Menu switch registration mode

Numeric parameter setting mode

NCU parameter setting mode

(Service adjustment is not available）

System test mode

Scan test mode

FAX test mode

Net work test mode

FAX

NET WORK

F-8-1

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Search results

Summary of Contents for FAXPHONE L190

Reviews:

Canon FAXPHONE L190, Service Manual, Page: 485 / 511

Search results

Summary of Contents for FAXPHONE L190

Reviews: