Canon FAXPHONE L190 Service Manual Download Page 31

Page: 31 / 511

1-12

Product Overview > Name of Parts > Cross Section > SADF

Rear Side

HAND

SET EXT.

LINE

HAND

SET EXT.

LINE

[7]

[5]

[6]

[1]

[2]

[3]
[4]

No.

Name

[1]

USB Device Port

[2]

LAN Port

[3]

External Device Jack

[4]

Telephone Line Jack

[5]

Power Supply Cord Slot

[6]

Rear Cover

[7]

Right Cover

F-1-10

Cross Section

■

DADF

[1]

[2]

[3]

[4]

[5]

No.

Name

[1]

Registration roller

[2]

Pickup roller

[3]

Separation pad

[4]

Delivery roller

[5]

Separation roller

■

SADF

[2]

[3]

[4]

[1]

No.

Name

[1]

Registration roller

[2]

Pickup roller

[3]

Separation pad

[4]

Delivery roller

F-1-11

F-1-12

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Search results

Summary of Contents for FAXPHONE L190

Reviews:

Canon FAXPHONE L190, Service Manual, Page: 31 / 511

Search results

Summary of Contents for FAXPHONE L190

Reviews: