manualshive.com logo in svg

Canon FAXPHONE L190, Service Manual, Page: 277 / 511

Share
Download
Canon FAXPHONE L190 Service Manual Download Page 277

4

4

4-201

4-201

Disassembly/Assembly > Controller System > Removing the Engine Controller PCB(D530) > Proce

d

ure

Disassembly/Assembly > Controller System > Removing the Engine Controller PCB(D530) > Proce

d

ure

4)Free the harness from the guide[A], and remove the main fan[1].
•  2 claws[2]

x2

[1]

[2]

[A]

Caution:
When mounting the main fan, attach the harness [2] to the upper-right side of the 
fan with the fan label [1] facing inwards.

[1]

[2]

F-4-516

F-4-515

Removing the Engine Controller PCB(D530)

 

■

Preparation

1) Remove the 

l

eft cover

2)Remove the copyboard cover and reader unit.
3)Remove the right cover
4)Remove the front cover unit.
5)Remove the upper cover.
6)Remove the duplex feed unit.
7)Remove the main controller PCB

 

■

Proce

d

ure

1)Remove the main controller mounting plate[1]
•  1 screw(with washer)[2]
•  1 screw(black TP)[3]

x2

[2]

[3]

[1]

F-4-517

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Reviews:

No comments