manualshive.com logo in svg

Canon FAXPHONE L190, Service Manual, Page: 206 / 511

Share
Download
Canon FAXPHONE L190 Service Manual Download Page 206

4

4

4-130

4-130

Disassembly/Assembly > Document Exposure/Feeder System > Removing the Flatbed Motor Unit (L418S/L410/L190) > Procedure

Disassembly/Assembly > Document Exposure/Feeder System > Removing the Flatbed Motor Unit (L418S/L410/L190) > Procedure

Removing the Flatbed Motor Unit (L418S/L410/L190)

 

■

Preparation

1) Remove the left cover. 
2)Remove the DADF unit and reader unit
3)Remove the DADF unit.
4)Remove the copyboard glass

 

■

Procedure

Caution.

When assembling/disassembling the copyboard glass, take care not to lose the 2 
CIS

 unit spacers [1].

 

When assembling/disassembling the copyboard glass, do not touch the copy reading
area [A] of the CIS unit.

[1]

[A]

1)Move the CIS unit[1].

[1]

2)Move the gear[1], and remove the belt[2] from the gear[3]

Caution.

Grease is applied on the shaft[1] of the contact sensor, so be careful not to let the 
belt[2] come in contact with the shaft.

[1]

[2]

F-4-305

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Reviews:

No comments