Canon EOS 2000D Page 19 Instruction Manual Download

Page: 19 / 144

Basic Operation and Settings

Wireless connection status can be checked with the camera’s <

lamp.

Wireless Connection Status

> lamp

Connection Status

> Lamp

Connected

Data is being sent or

received

Blinking rapidly

Waiting for connection/

Waiting for reconnection

Blinking

Connection error

Blinking

somewhat

rapidly

Cable Connection Cautions



When [

3: Wi-Fi/NFC

] is set to [

Enable

], connection via interface cable

or HDMI cable is disabled. Set [

3: Wi-Fi/NFC

] to [

Disable

] before

connecting a cable.



When the camera is connected to Connect Station, a computer, printer,
GPS receiver, TV set, or any other device via a cable, settings for [

Wi-Fi/

NFC

] cannot be changed. Disconnect the cable before changing any

settings.

Cards



If there is no card in the camera, it cannot be connected wirelessly.
Additionally, for [

] and [

], the camera cannot be connected

wirelessly if there are no images saved on the card.

Using an Eye-Fi Card



When [

3: Wi-Fi/NFC

] is set to [

Enable

], image transfer using an Eye-Fi

card is disabled.

Summary of Contents for EOS 2000D

















































































































































Search results

Summary of Contents for EOS 2000D

Reviews:

Related manuals for EOS 2000D

Brands by name

Popular brands

Canon EOS 2000D, Instruction Manual

Search results

Summary of Contents for EOS 2000D

Reviews:

Related manuals for EOS 2000D

Brands by name

Popular brands