Canon EOS 1300D (W) Wireless Function Instruction Manual Download Page 2

Page: 2 / 144

By connecting to a Wi-Fi



network or other device supporting this

camera’s wireless functions, you can perform tasks such as transferring
images or controlling the camera.

* Use the latest firmware.

Introduction

What You Can Do Using the Wireless Functions

(CANON iMAGE

GATEWAY)

(5) Send images to a

Web service

(1) Connect to a smartphone

(3) Print images using

a Wi-Fi printer

(2) Transfer images

between cameras

(4) Save images to

Canon Connect Station*

CANON iMAGE GATEWAY Web services are not supported in certain
countries and areas. For information on supported countries and areas,
refer to the Canon Web site (www.canon.com/cig).

Summary of Contents for EOS 1300D (W)

















































































































































Search results

Summary of Contents for EOS 1300D (W)

Reviews:

Related manuals for EOS 1300D (W)

Brands by name

Popular brands

Canon EOS 1300D (W), Wireless Function Instruction Manual

Search results

Summary of Contents for EOS 1300D (W)

Reviews:

Related manuals for EOS 1300D (W)

Brands by name

Popular brands