Canon EOS 1300D (W) Wireless Function Instruction Manual Download Page 129

Page: 129 / 144

129

Responding to Error Messages



Web service setting operation may have failed.



Connect the camera and computer using an interface cable and
reconfigure Web service settings using EOS Utility (p.91).



Is the camera’s registration information or Web service
registered on the camera deleted on CANON iMAGE
GATEWAY?



Connect the camera and computer using an interface cable and
reconfigure Web service settings using EOS Utility (p.91).



The root certificate has expired or is invalid.



Connect the camera and computer using an interface cable and
reconfigure Web service settings using EOS Utility (p.91).



This error may be displayed if the camera’s time setting is
significantly off from the actual time. Check if the correct time is set
on the camera.



Is the network connected?



Check the connection status of the network.



CANON iMAGE GATEWAY is under maintenance or load is
concentrated temporarily.



Try connecting to the Web service again later.

122: Connect to a computer, and correct the settings for

the Web service with EOS software.

123: Cannot log in to Web service. Connect to a computer

and correct the settings with EOS software.

124: Invalid SSL certificate. Connect to a computer and

correct the settings with EOS software.

125: Check the network settings

126: Could not connect to server

Summary of Contents for EOS 1300D (W)

















































































































































Search results

Summary of Contents for EOS 1300D (W)

Reviews:

Related manuals for EOS 1300D (W)

Brands by name

Popular brands

Canon EOS 1300D (W), Wireless Function Instruction Manual

Search results

Summary of Contents for EOS 1300D (W)

Reviews:

Related manuals for EOS 1300D (W)

Brands by name

Popular brands