Canon DR-4010C - imageFORMULA - Document Scanner Page 126 User Manual Download

Page: 126 / 143

8-1

Chapter 8

Job Registration Tool Settings

This chapter describes Job Registration Tool settings for job functions. Refer to Section

“3-4 Job

Function,” on p. 3-9

for details.

8-1 Starting the Job Registration Tool

The Job Registration Tool is a TWAIN-compliant application program that installs with the ISIS/

TWAIN driver, and is started by the following procedure.

Click the Windows [Start] button, and click then [Programs] ([All Programs] for Windows XP)

[DR-4010C]

[Job Registration Tool].

The Job Registration Tool starts.

(See “8-2 Job Registration Tool Settings Dialog Box,” on p. 8-

2.)

Summary of Contents for DR-4010C - imageFORMULA - Document Scanner
















































































































































Search results

Summary of Contents for DR-4010C - imageFORMULA - Document Scanner

Reviews:

Related manuals for DR-4010C - imageFORMULA - Document Scanner

Brands by name

Popular brands

Canon DR-4010C - imageFORMULA - Document Scanner, User Manual

Search results

Summary of Contents for DR-4010C - imageFORMULA - Document Scanner

Reviews:

Related manuals for DR-4010C - imageFORMULA - Document Scanner

Brands by name

Popular brands