Canon CR-X300 User Manual Download Page 84

Page: 84 / 114

Updating the firmware.

Device Information

[Model Name], [Firmware Version]

Displays the camera information.

Update Firmware

Updating the firmware.

[Restore Default

ettings]

Restores the default settings when the firmware is updated.

When set to [Restore], initialization will be performed except for the following settings.

• Network Settings

• NTP Server

• HTTP Server

• Host Access Restrictions

• Time Zone

• Certificates

• SSL/TLS

• Administrator Name

• Administrator Password

[Update Firmware]

Click […] to select the firmware file for updating and click [Execute]. When a confirmation message is displayed, click [OK]

to start Update Firmware. The POWER lamp on the rear of the camera blinks during the update.

After the firmware is updated, the camera will be rebooted.

[System] > [Maintenance] > [Update Firmware]

Important

Do not turn off the power to the camera while performing [Update Firmware]. Turning off the camera may prevent the camera from
operating correctly.

Summary of Contents for CR-X300



















































































































Search results

Summary of Contents for CR-X300

Reviews:

Related manuals for CR-X300

Brands by name

Popular brands

Canon CR-X300, User Manual

Search results

Summary of Contents for CR-X300

Reviews:

Related manuals for CR-X300

Brands by name

Popular brands