manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

III. BASIC SERVICING CHART

The printer unit does not have parts that require periodical servicing. The following

work is recommended to prolong the life of each part and, ultimately, the life of the print-
er unit itself.

Items to Clean

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 9  MAINTENANCE AND SERVICING

9-2

Unit

Pick-up feeding

Development

Fixing assem-
bly

Intermediate
transfer drum

Charging
assembly

Part

Multifeeder roller

Cassette pick-up roller

Feeding roller 1

Feeding roller 2

Separation roller

Separation pad

Registration roller assembly

Separation guide

Transparency sensor 1/2

Sub cover sheet

Toner catch tray

Fixing assembly inlet guide

Upper/lower fixing separation
guide

Density sensor

Pre-exposure LED assembly

Secondary pre-transfer charging
assembly

Separation static assembly

Remarks

Use lint-free paper or alcohol.

Use lint-free paper.

Use lint-free paper. If the dirt cannot
be removed, use alcohol on the
rubber area and solvent on other
areas.

Do not remove the spring when
cleaning; a displaced spring will
cause skew movement of paper or
jams. Correct the spring if displaced.

Use lint-free paper.

Use a blower brush.

Use lint-free paper or alcohol.

Remove any cake of toner.

Use solvent.

Use solvent to remove cakes of
toner. (Do not force.)

Use the special brush.

Use a cleaning lever.

Note:

1. As a rule, do not clean the following:

• ITD cleaning roller
• Photosensitive drum cartridge
• Secondary transfer belt assembly

2. The surface of the intermediate transfer drum may develop condensation during

installation work. If such happens, dry wipe the surface with lint-free paper. If the
output images are soiled, suspect dirt on the surface of the intermediate transfer
drum. To correct, wipe it with a flannel cloth moistened with water, and then dry
wipe it with lint-free paper.

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

UBI EasyCoder 501 SA Service Manual preview
EasyCoder 501 SA
Brand: UBI Pages: 214
UBI EasyCoder 401 Technical Manual preview
EasyCoder 401
Brand: UBI Pages: 64
Oki C610cdn Brochure & Specs preview
C610cdn
Brand: Oki Pages: 4
Kyocera ECOSYS M8124cidn Quick Manual preview
ECOSYS M8124cidn
Brand: Kyocera Pages: 44
NEC SuperScript 610 User Manual preview
SuperScript 610
Brand: NEC Pages: 105
Oki B4600 Series Specifications preview
B4600 Series
Brand: Oki Pages: 2
Xerox WorkCentre PRO 35 Specifications preview
WorkCentre PRO 35
Brand: Xerox Pages: 13
Ricoh MP 2554SP Series Configuration Manual preview
MP 2554SP Series
Brand: Ricoh Pages: 1
Xerox Document Centre 255 LP Reference Manual preview
Document Centre 255 LP
Brand: Xerox Pages: 158
TEC tecjet 6090DTG-dx5 User Manual preview
tecjet 6090DTG-dx5
Brand: TEC Pages: 73
Mooreco Makerspace 91413 Assembly Instructions Manual preview
Makerspace 91413
Brand: Mooreco Pages: 10
Oki B700 Series Installation Instructions preview
B700 Series
Brand: Oki Pages: 4
Ovislink AirLive WP-203G User Manual preview
AirLive WP-203G
Brand: Ovislink Pages: 132
AURES Posligne ODP-1000 Quick Start Manual preview
Posligne ODP-1000
Brand: AURES Pages: 4
Kyocera ECOSYS FS-6530MFP Specfications preview
ECOSYS FS-6530MFP
Brand: Kyocera Pages: 2
3D Printing Systems UP Plus 3D Manual preview
UP Plus 3D
Brand: 3D Printing Systems Pages: 56
Olivetti d-Color MF1600 Service Manual preview
d-Color MF1600
Brand: Olivetti Pages: 204
Belkin F1UP0002 Quick Installation Manual preview
F1UP0002
Brand: Belkin Pages: 2

Brands by name

Popular brands

Load more brands