Canon Colorado M Series Operation Manual Download Page 182 | Manualshive

Page: 182 / 378

background image

Start manual maintenance

Introduction

In case of quality issues that are not solved by automatic maintenance with nozzle optimization,
start manual maintenance.

Perform any or all of the listed actions on the operator panel.

You can print a nozzle optimization chart to optimize the nozzles.

Procedure

1.

On the operator panel tap on the [Tools] icon on the right.

2.

Tap on [Manual maintenance].

NOTE

We recommend that you check the [Automatic nozzle optimization] when you are experiencing
print quality issues. After you have cleaned the matrix plate and the printheads the recovered
nozzles have to be switched on again (if you do not check this option the nozzles will keep the
status "do not use").

3.

When you want to print nozzle optimization charts to optimize the nozzles:

1.

Make sure [Automatic nozzle optimization] is selected.

2.

Select a roll to print the nozzle optimization charts on.

Start manual maintenance

182

Chapter 6 - Maintain the system

«
...
180
181
182
183
184
...
»

Summary of Contents for Colorado M Series



























































































































































































































































































































































































Reviews:

No comments

Related manuals for Colorado M Series

Brand: D-Link Pages: 38

Epress EtherNetwork DP-301P+

Brand: D-Link Pages: 2

Brand: TASKalfa Pages: 36

Brand: Xerox Pages: 3

Brand: Xerox Pages: 13

Brand: Xerox Pages: 8

Brand: Xerox Pages: 41

Versant 3100 Press

Brand: Xerox Pages: 45

Brand: Olivetti Pages: 16

ECOSYS M8124cidn

Brand: Kyocera Pages: 44

Brand: Oki Pages: 40

Document Centre 255 LP

Brand: Xerox Pages: 158

tecjet 6090DTG-dx5

Brand: TEC Pages: 73

Brand: Oki Pages: 57

Brand: oti Pages: 33

3600B - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

Brand: Riso Pages: 66

Brand: Hamlet Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands