manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 359

Waves in media

Introduction

Solve media touches or print quality artefacts caused by waves in the media. When media is
weak and or of a relatively narrow media width (<1000mm) the vacuum suction can be too low
and the media will start to move over the platen in a wave motion. Follow the procedure below.
You can stop at any time in the procedure when the problem is solved.

Procedure

1.

Increase the [Vacuum power] settings in the RIP. Increase with steps of 10%. For each step you
increase and have changed the setting: reload the media before you continue printing. Observe
the media movement on the platen first, before you increase the vacuum power again. 

Change

the media settings on page 67

.

2.

Perform media calibration. 

Calibrate the media on page 113

.

3.

Use a different media type.

Waves in media

Chapter 9 - Troubleshooting and support

359

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands