manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 350

Vertical banding

Introduction

Problem description

Cause

Action

Sharp lines or bands.

Matching the roller
positions.

Some media are very
sensitive to mechani-
cal deformation.

Try a different medi-
um.

More gradual varia-
tion, some periodicity

 

Selected print mode is
to fast.

Select a slower print
mode see 

Select a

print mode on
page 75

.

If you are printing in a
high speed gloss (1
and 2 pass) print
mode, select a slower
print mode.
If you are printing in
Matte Specialty, you
can select the mono-
directional strategy
option.

Mechanical problem.

Check the carriage
guidance, bearings or
lubricators.

Sharp lines or bands

Gradual variation vertical banding

Vertical banding

350

Chapter 9 - Troubleshooting and support

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands