Canon Colorado 1630 Operation Manual Download Page 347

Page: 347 / 388

Lines within swaths

Introduction

Problem description

Cause

Action

Sharp OD/gloss lines
for a single mono-col-
or and its correspond-
ing mixed colors.

A single light line
(doesn’t repeat in next
swath)?

Detected too late for
compensation in that
swath.

Cannot be solved (a
slower print mode will
reduce the problem).

A light line that re-
peats in multiple
swaths, high quality
mode or better.

Probably undetected
nozzle failure or side
shooter.

Run maint
nozzle optimization.

Dark/light/gloss lines (single mono-color/not at
swath boundary)

Probably compensa-
ted nozzle failure, but
still (somewhat) visi-
ble.

Run maint
nozzle optimization (to
prevent the nozzle fail-
ure).

Try a different print
mode (to reduce visi-
bility).

Many lines or a thin band, doesn’t go away af-
ter manual maintenance

Run printhead test
chart. See:

Analyze

the printhead quality
check chart on
page 262

. If lines are

visible over multiple
printhead colors, veri-
fy if the printer is cor-
rectly cleaned (fibers).

Follow the procedure below. You can stop at any time in the procedure when the problem is
solved.

Lines within swaths

Chapter 9 - Troubleshooting and support

347

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Search results

Summary of Contents for Colorado 1630

Reviews:

Brands by name

Popular brands

Canon Colorado 1630, Operation Manual

Search results

Summary of Contents for Colorado 1630

Reviews:

Brands by name

Popular brands