manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 333

Remove media from the paper path

Introduction

In case of a media jam or a carriage crash you can remove the media from the paper path.

Before you begin

• Wear the Colorado 1630 prescribed Microflex gloves for handling ink.
• Use a knife that is sharp enough to cut the media.

CAUTION

Wear the prescribed gloves when contact with ink or maintenance materials is possible. Gloves

should always overlap sleeves. Follow the Safety Data Sheets (SDS) guidelines carefully in

order to ensure maximum safety.

IMPORTANT

Watch out with uncured ink. Strictly follow the steps below, to make sure you do not pull media

with uncured ink through the system.

Procedure

1.

Locate the winder on the media output side of the printer. If present, take the tension bar out.
You can lift the tension bar up by manually winding the take-up media roll.

Remove media from the paper path

Chapter 9 - Troubleshooting and support

333

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands