manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 323

Turn the printer on and off

Introduction

The printing system is powered on by the service technician at installation. You can turn the
printer on or off via the button on the media output side.

Procedure

1.

Move to the media output side and locate the on/off button under the operator panel.

2.

Push the button
The printer is switched on or off. The system is kept in standby mode, so power to the system is
never cut.

NOTE

Before you turn off the printer make sure:
• The printer is not busy.
• There is no media on the platen.
• The printer is in a state where maintenance is possible.

Turn the printer on and off

Chapter 9 - Troubleshooting and support

323

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands