manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 296

Restore a backup

Introduction

When you have made a backup you can restore it.

Before you begin

You need to have a backup created before. It is highly recommended to have exported a backup.
For more information, see 

Make a backup on page 295

.

Procedure

1.

Open the settings editor.

2.

Click on [Support] 

→

[Backups].

3.

In case of an external backup, exported during a backup operation, click on [Import]. Browse to
the external backup and confirm the import operation.
When imported with a confidential data passphrase and this passphrase does not match the
passphrase of the backup, the screen displays a warning that the confidential data is not available
for restoring.

4.

Check the box in front of the backup file.

5.

Click on [Restore user configuration].

6.

Click on [Ok] to restore the configuration.

Restore a backup

296

Chapter 8 - Configure the network and security settings

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands