manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 283

Certificates overview

Introduction

There are two kinds of certificates:
• Trusted certificates
• Identity certificates

Trusted certificates

Trusted certificates allow the controller to recognize Root and intermediate certificates that may
be sent by :
• The mail server, with secure communication via HTTPS, when configuring or using it for

System administrator password recovery.

• The proxy server, during communication with the back office, when Remote Service

communication is enabled.

Identity certificates

Identity certificates are required to allow a browser to establish a HTTPS connection with the
controller for access to the settings editor.

Actions

You can:
• Import trusted certificates used by your company. Ask the IT administrator. For more

information, see 

Import a trusted certificate on page 284

• Enable the use of a HTTPS protocol, by requesting and uploading a certificate. For more

information, see 

Enable the use of HTTPS on page 285

Certificates overview

Chapter 8 - Configure the network and security settings

283

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands