manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 265

Calibrate the printhead carriage

Introduction

When your image is blurred or fuzzy the registration can be off. Calibrate the printhead carriage
to align the registration.

Before you begin

First perform the following actions to try and solve your problem, before you calibrate the
printhead carriage:
1. Check if you have filled in the correct [Media thickness ] in the RIP's media settings. For more

information, see 

Change the media settings on page 67

.

2. Perform media calibration. For more information, see 

Calibrate the media on page 113

.

NOTE

• You can only perform printhead calibration when you print without winding. For more

information, see 

Print without winding on page 131

.

• You have to use a media width that is larger than 1270 mm (50 inch).
• You have to use a media type that can be used for printing without winding.
• You have to use a smooth, white, opaque, non-reflective media for the printhead calibration of

one of the following categories:
• Heavy paper > 200 gsm (54 lb bond)
• Paper 120-200 gsm (32-54 lb bond)
• Film
• Polymeric & cast self-adhesive vinyl
• Thick film > 200 um (0.0079 inch)

Procedure

1.

Load the correct media type. For more information, see 

Load a media roll (position 1) on page 82

.

2.

On the operator panel tap on the [Tools] icon on the right.

3.

Tap on [Printhead carriage calibration].

Calibrate the printhead carriage

Chapter 7 - Improve quality

265

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands