manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 253

Clean the ruler

Introduction

The printer uses a ruler to control the printhead carriage. A polluted ruler interferes with control
of the printhead carriage. In case of pollution, you can clean the ruler.

Video: 

Clean the ruler

.

NOTE

You can clean a ruler marked with a green dot. Do not clean a ruler that is not marked with a

green dot.

When to do

If the operator panel shows error 

5709

, clean the ruler.

Before you begin

Use Colorado 1630 prescribed:
• Microflex gloves for handling ink
• Lint free cloths
• Cleaning liquid IPA

NOTE

For information on the prescribed maintenance materials, see 

List of Colorado 1630

maintenance materials on page 255

.

CAUTION

Wear the prescribed gloves when contact with ink or maintenance materials is possible. Gloves

should always overlap sleeves. Follow the Safety Data Sheets (SDS) guidelines carefully in

order to ensure maximum safety.

IMPORTANT

Use the prescribed cleaning liquid. Do not use any other cleaners.

Clean the ruler

Chapter 6 - Maintain the system

253

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands