manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 234

Vacuum the chiller and check the fluid level (new design)

Introduction

It is advised to vacuum the chiller every month to keep the printer in the best condition.
Vacuuming the chiller is part of periodic maintenance so the operator panel gives a warning
when you should vacuum the chiller. Always check the fluid level when you vacuum the chiller.

Video: 

 Vacuum the chiller

NOTE

There are 2 types of chillers. In the first design, the condenser surface is located on the left side

of the chiller. In the new design, the condenser surface is located directly behind the cover. This

procedure describes the new design.

First design

New design

Before you begin

Use Colorado 1630 prescribed:
• Screwdriver (Torx-25)
• Vacuum cleaner with a brush head

Check the fluid level

To check the fluid level, locate the level gauge glass behind the right-hand side of the cover.

NOTE

Do not remove this section of the cover. You can see the level gauge glass through the openings

in the cover.

If the fluid level is near the bottom of the green zone, you must refill the chiller.

Vacuum the chiller and check the fluid level (new design)

234

Chapter 6 - Maintain the system

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands