manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 215

Replace the knife

Introduction

Replace the knife when the knife does not cut your media correctly anymore.

Video: 

 Replace the knife

Before you begin

Use Colorado 1630 prescribed:
• Microflex gloves for handling ink
• Screwdriver (Torx-25) for the cover
• Screwdriver (Torx-6) for the knife
• Knife

NOTE

For information on the prescribed maintenance materials, see 

List of Colorado 1630

maintenance materials on page 255

.

CAUTION

Wear the prescribed gloves when contact with ink or maintenance materials is possible. Gloves

should always overlap sleeves. Follow the Safety Data Sheets (SDS) guidelines carefully in

order to ensure maximum safety.

Procedure

1.

Open the top cover from the media input side.

2.

Put on the Colorado 1630 approved gloves.

3.

Locate the knife and move it from the left to the right.

Replace the knife

Chapter 6 - Maintain the system

215

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands