Canon C831002 - PowerShot S20 3.2MP Digital Camera Page 21 User Manual Download

Page: 21 / 88

Preparing the Camera

Battery Performance

• The actual performance may vary from the above

data according to the shooting conditions and the
selected recording mode.

Test Conditions

Recording: 73

F (23

C), (Large)/ (Fine), Zoom

used, flash used once every 4 shots

Replay:

F (23

C), continuous replay, 5 seconds

per image

Using the AC Adapter

You are recommended to use the AC adapter
when you will be using the camera for a
relatively long period of time. Attach the AC
adapter as shown below.

• The CAMERA indicator on the compact

power adapter will shine red when it is
powering the camera.

• Always remove the plug from the electrical

outlet when you have finished using the
camera.

• Battery Pack NB-5H cannot be charged

while the compact power adapter is
used to power the camera.

• Do not use the compact power adapter

to power any device other than one for
which Battery Pack NB-5H is specified.

No. of Images

Replay

LCD Monitor LCD Monitor (Minutes)

Off

Battery Pack NB-5H

Approx.

(fully charged)

55 shots

230 shots

50 min.

2CR5 Lithium Battery

Approx.

(Sanyo brand, new)

65 shots

400 shots

80 min.

DC Coupler
DR-100A

Cable Cover

DC Terminal

Camera
Indicator
(DC Output)

Compact Power Adapter

Summary of Contents for C831002 - PowerShot S20 3.2MP Digital Camera

























































































Search results

Summary of Contents for C831002 - PowerShot S20 3.2MP Digital Camera

Reviews:

Related manuals for C831002 - PowerShot S20 3.2MP Digital Camera

Brands by name

Popular brands

Canon C831002 - PowerShot S20 3.2MP Digital Camera, User Manual

Search results

Summary of Contents for C831002 - PowerShot S20 3.2MP Digital Camera

Reviews:

Related manuals for C831002 - PowerShot S20 3.2MP Digital Camera

Brands by name

Popular brands