Canon BJC-6200 Reference Manual Download Page 14

Page: 14 / 281

Printing on Paper and Other Media

Media Sizes You Can Use with the Printer

The following table lists the standard paper sizes that can be used with the printer.

You can also use custom paper sizes within the following ranges.

Width:

100.0mm to 420.0mm (3.94" to 16.54")

Height:

100.0mm to 594.0mm (3.94" to 23.39")

Media of the following weight can be loaded for printing: 64g/

to 105g/

Paper

Width x Height

148.0mm x 210.0mm/210.0mm x 148.0mm

182.0mm x 257.0mm

210.0mm x 297.0mm

Letter

8.5" x 11.0" (215.9mm x 279.4mm)

Legal

8.5" x 14.0" (215.9 x 355.6mm)

Envelope (European DL)

220mm x 110mm

Envelope (US Com. #10)

9.5" x 4.1" (241.3mm x 104.77mm)

Glossy Photo Cards

119.6mm x 215.9mm (with borders)
101.6mm x 152.4mm (final size without borders)

Summary of Contents for BJC-6200


























































































































































































































































































Search results

Summary of Contents for BJC-6200

Reviews:

Brands by name

Popular brands

Canon BJC-6200, Reference Manual

Search results

Summary of Contents for BJC-6200

Reviews:

Brands by name

Popular brands