Canon Arizona 1300 Series User Manual Download Page 202 | Manualshive

Page: 202 / 248

background image

Empty Ink Waste Trays

Introduction

There are two waste trays. The Purge Waste Tray is located under the Maintenance station. It
catches ink purged from either Manual maintenance or Automated printhead maintenance. The
Spit Waste Tray is located below the ink spit catcher. It accumulates waste ink from printhead
spitting.

[93] 1 = Purge Waste Tray 2 = Spit Waste Tray

When to do

Empty both waste trays weekly.

CAUTION

Wear gloves when contact with ink or maintenance materials is possible. Gloves should always
overlap sleeves. Follow the ink related Safety Data Sheets (SDS) guidelines carefully in order to
ensure maximum safety. For example use Ansell Microflex 93-260 gloves, which offer a
protection against UV inks and flush up to one hour. Pollution with other chemicals can shorten
the protection time against UV inks and flush.
Wear eye protection as prescribed in this document when performing a task or action in this
area.

CAUTION

UV inks and flush liquids can be harmful if not properly handled. Follow always the Safety Data
Sheets (SDS) guidelines carefully in order to ensure maximum safety.

NOTE

Although the carriage is oriented so that the nozzles spit into the slots in the spit catcher, some
ink will find its way onto the flat surfaces. Open the maintenance drawer to check the surface of
the spit catcher daily. If you see any ink wipe it up with a clean cloth or paper towel.

Equipment

• Foam Tipped Swab or Cloth-Poly Wipe

Empty Ink Waste Trays

202

Chapter 11 - Maintenance

«
...
200
201
202
203
204
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

Brand: Canon Pages: 358

Brand: Xerox Pages: 192

Brand: Xerox Pages: 40

ApeosPort-III C7600

Brand: Xerox Pages: 369

MAGICARD 300plus

Brand: Ultra electronics Pages: 45

Brand: Xerox Pages: 24

Brand: BenQ Pages: 6

Brand: Lexmark Pages: 4

MP 2554SP Series

Brand: Ricoh Pages: 1

Line Printer VIII

Brand: Radio Shack Pages: 54

Brand: Lexmark Pages: 57

Brand: Mitsubishi Pages: 2

Brand: Oki Pages: 132

Brand: Xerox Pages: 109

Brand: Paradise POS Pages: 275

Brand: Axiohm Pages: 6

Brand: GeBe Pages: 25

Brand: Plas-Ties Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands