Canon Arizona 1300 Series User Manual Download Page 199 | Manualshive

Page: 199 / 248

background image

Replace the UV LED unit Filter

Introduction

The printer has two UV LED units, one on each side of the carriage, to cure the UV ink during
printing. The filters in these UV LED units have a limited lifetime and must be replaced by the
operator to prolong the life of the unit and maximize curing efficiency.

When to do

These filters should be changed every two weeks.

Before you begin

It is recommended to wear gloves when handling dirty UV LED unit filters due to the possibility of
partially cured ink deposits.

Failure to replace dirty filters will result in lamps operating at a higher temperature causing
premature failures of internal components and UV LED units.

How to Replace the UV Lamp Filters

It is not necessary to shut the printer power off the while replacing the UV LED unit filters.
However, allow a few minutes after printing for the UV LED units to cool down.

NOTE

Wear cotton or nitrile gloves when handling UV LED unit. Avoid bare skin contact with filters that

are contaminated with partially cured ink.

Procedure

1.

Remove the UV lamp filter.

2.

Place a new filter in the lamp assembly.

Replace the UV LED unit Filter

Chapter 11 - Maintenance

199

«
...
197
198
199
200
201
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

Brand: CAB Pages: 263

All in One Printer

Brand: Xerox Pages: 3

Brand: Acadian Robotics Pages: 2

Brand: Datecs Pages: 29

Brand: Oki Pages: 154

Brand: Oki Pages: 121

Brand: Oki Pages: 52

Brand: Oki Pages: 96

Brand: Oki Pages: 20

MC560 MFP CX2032

Brand: Oki Pages: 247

Brand: Olivetti Pages: 82

Brand: Oki Pages: 80

B-470-QQ Series

Brand: TEC Pages: 32

Brand: Copystar Pages: 2

Brand: Oki Pages: 182

Brand: Evolis Pages: 45

Brand: Aleph Objects Pages: 26

BIZHUB 8050 CF5001

Brand: Konica Minolta Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands