manualshive.com logo in svg

Canon 2417B002, User Manual, Page: 89 / 157

Share
Download
Canon 2417B002 User Manual Download Page 89

6-2

Chapter 6   Practical Examples

1.

Messages

There are two types of display panel messages: “status indicator messages” and “error messages” that appear when the scanner 
encounters a problem.

Status Display

The following messages appear on the display panel to 
indicate the scanner’s operating state:

■

Counting...

Status:

 Operating in Count-Only mode.

■

Insert the Sheet

Status:

 In the Cleaning Mode, waiting for the cleaning 

sheet to be inserted. 

■

Press Start Key

Status:

 Waiting. Load a document and press the Start key.

■

Ready

Status:

 The scanner is ready to use.

■

Scanning...

Status:

 Scanning is in progress.

■

Sleeping...

Status:

 The scanner is entering the Sleep mode. Press any 

key to recover.

■

Wait...

Status:

 The scanner is busy processing. Wait until the 

display changes.

■

Verifying…

Status:

 The scanner is verifying a scan.

■

Replace Roller

Status:

 It is time to replace the rollers (the number of fed 

pages has exceeded 500,000). 

(See “Roller Replacement 

Cycle” on p. 5-12.)

Summary of Contents for 2417B002






























































































































































Reviews:

No comments