background image

 

vi 

LIST OF FIGURES 

 
Figure 1.  M-MODULE Installation ............................................................................................ 5 
Figure 2.  M220 Functional Block Diagram................................................................................. 7 
Figure 3.  M220 Switching Schematic ......................................................................................... 9 
Figure 4.  Jumper Positions ....................................................................................................... 10 
Figure 5.  I/O Registers ............................................................................................................. 12 
 
Figure A-1. Front Panel I/O Signals......................................................................................... A-1 
 

LIST OF TABLES 

 

Table I.  Specifications ................................................................................................................ 2 
Table II.  I/O Address Map/Command Summary....................................................................... 11 
Table III.  M/MA Module PROM IDENT Words...................................................................... 14 

Table IV.  Matrix Drive

.......................................................................................................... 16 

 

 
 

C&H Technologies, Inc. <> 445 Round Rock West Drive <> Round Rock, Texas  78681 <> www.chtech.com

Summary of Contents for M 2 2 0































Reviews: