background image

Do NOT operate if you smell smoke coming from your corn appliance.  Push OFF on the control
board, monitor your stove and call your dealer.

NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID or
similar liquids to start or ‘freshen up’ a fire in this appliance.  Keep all such liquids well away from
the stove while it is in use.

Do NOT unplug the heater if you suspect a malfunction.  Push OFF on the control board and
inspect the heater.

Do NOT operate the stove if the flame become dark & sooty or if the burn pot overfills with corn.
Push OFF on the control board and periodically inspect the stove.

NEVER try to repair or replace any part of the stove unless instructions for the consumer are
given in this guide.  All other work should be done by a trained technician.

The viewing door and ash bin must be closed and latched during operation.

NEVER block free airflow through the open vents of the unit.

Contact your local building officials to obtain a permit and information on any installation
restrictions or inspection requirements in your area.

Notify your insurance company of this stove.

The corn appliance exhaust system works with negative combustion chamber pressure and a
slightly positive chimney pressure.  Therefore the exhaust system MUST BE COMPLETELY AIR TIGHT
and properly installed.  All pellet joints must be sealed with HI-TEMP RTV SILICONE SEALANT and
at least 3 sheet metal screws to each other as well as to the stove.

This unit must be properly installed to prevent the possibility of a house fire.  The instructions must
be strictly adhered to.  Do NOT use makeshift methods which may compromise the installation.

Your stove requires periodic maintenance and cleaning.  Failure to maintain your stove may
lead to smoke spillage in your home.

Allow the appliance to cool before carrying out any maintenance or cleaning.  Ashes must be
disposed of in a metal container with a tight fitting lid.  The closed container of ashes should be
placed on a non-combustible surface or on the ground well away from all combustible materials
pending final disposal.

This stove is designed and approved for shelled corn fuel and wood pellets.  Any other type of
fuel burned in this stove may void the warranty and safety listing.

This appliance will not operate during a power outage.  If a power outage does occur, check the
stove for smoke spillage and open a window if any smoke spills into the room.

Keep foreign objects out of the hopper.

SAFETY

PRECAUTIONS

12

Summary of Contents for Corn Stove

















Reviews: